Quadstar Roller Derby Skates (No Bumper)

$109.00 $309.00

Use our size chart to get the perfect fit: https://bont.com/pages/sizing/

Final stock, limited sizes remaining, sold as is!

This item is only available to ship to an address within the USA.
Do not heat mold in the oven, use a hairdryer to heat them. These skates are on closeout because they only have double toe protection rather than the new upgraded triple-layer toe protection. 

The Quadstar roller derby skate breaks the mold of what materials an entry level skate should be made from and it takes performance beyond most brands high-end boots. All for a fraction of the price!

The thermoplastic in the heel allows you to mold your boot with a hairdryer to obtain a custom fit in under 10 minutes. This is especially good for skaters with skinny or wide ankles. 

Made with 100% Genuine Australian leather with triple layer protection in the toe area. The boot features an adjustable Velcro top closure to hold your foot tight and a rear heel loop to put your laces through.

The fiberglass-reinforced Ignite plate is very lightweight and has 20-degree action trucks. The package will come with Ballistic wheels, made with premium high rebounding urethane, rounds out the Quadstar super light setup.

Features
  • Base: Fiberglass
  • Outer skin: Australian leather
  • Liner: Suede-L
  • Boot height: High
  • Heel rise: 6mm
  • Innersole: EVA with fabric
  • Heat moldable: Fully heat moldable base utilizing epoxy thermoset resin
  • Padding: Memory foam
  • Size options: 1 - 8.5, 10.5
  • Fit options: Standard

  • MANUFACTURING

    Manufacturing skates by hand, inside out, is a method Bont retains and is exceptionally proud of. The manufacturing process is far more skill-intensive and time-consuming than other manufacturing processes. Perhaps, most importantly, this enables Bont skates to lead the industry in performance. It does, however, result in a higher production cost than mainstream skate construction methods.

    We continue to develop and refine our manufacturing process to maintain the best delivery of our high-quality products. For example, processes such as the use of generic vacuum boxes for the curing of carbon have been replaced. Today, for carbon curing, we use methods such as pressure wrapping. Pressure wrapping provides four atmospheres of pressure rather than one atmosphere you find in traditional vacuum forming.

    Inze Bont’s, the renowned skate designer, engineering, has allowed our production line to optimize the manufacturing of our handmade monocoque skates in the most time-efficient manner possible.

    Our innovative manufacturing processes match our drive for design innovation. Lighter, Stronger, Faster.

    Read our process for Last Design, Footbed, Liner, Anti-Stretch, Carbon Fiber, Upper, and more in the self-titled sections below.

  • LAST DESIGN

    What is a Last? The Last is a plastic replica of a foot which the boot is built around.

     

    Here at Bont, we have been perfecting our Lasts since 1975! and the process is ongoing. Unlike the standard Last many companies use, Bont continually focuses on developing and improving our Lasts so that your boots fit right out of the box.

     

     Last Design

  • FOOTBED

    Footbed

    Made in house, from heat-moldable EVA, the Bont Footbed is the first piece of a boot added to the Last. To ensure it retains its extreme light-weight and heat-moldable characteristics, the Footbed is 65A hardness and only 3mm thick.

     

     

  • LINER

    We reviewed hundreds of different types of Liners before choosing a suitable product to use in our Bont boots. Bont uses Microfiber, Suede-Like, and Durolite as our liners. Ensuring we are working towards sustainability and animal welfare, Bont is using Vegan-friendly products. In short, our liners are light-weight, durable, fight odor, and do not easily break down with sweat.

     

     

    liner-suede-l liner-microfiber liner-durolite

  • ANTI-STRETCH

    Our proprietary Anti-Stretch material shares similar strength characteristics with Kevlar. We add this material between the outer layer and the skin, which assists prevent the boot from stretching.

    To ensure the material does not move, we stitch it to the outer layer and bond it to the liner. In short, this Anti-Stretch material becomes a part of the boots’ structure. As a result, Bont boots do not stretch out as much as competitors’ boots.

    Anti Stretch

     

  • UPPER

    The Bont Upper, the upper section of the boot, is lightweight, glued and sewn onto the boot. We punch holes by hand through the Upper and the Liner for ventilation. Buckles and straps are attached to ensure your foot is pulled down and pushed to the back. Finally, we clean the excess glue off, and the boot is ready for skating. To be deemed ready for action, the boot is required to pass sixteen stages of independent quality control. As a result, we provide you with the best strength to weight ratio on the market.

     

     

  • PADDING

    This boot utilizes closed cell memory foam. Ensuring your shoe remains lightweight in wet conditions, Bont padding does not retain water. Additionally, this ensures sweat which can begin to break down the durability of the shoe is not absorbed.

     

     

    Padding

  • RESIN DEVELOPMENT

    Here at Bont, we have been conducting resin development for over 45 years. We formulated a resin that is super stiff, yet moldable at low temperatures. Furthermore, fast cure time is critical for our requirements. Additionally, we are one of the only boot manufacturers who develop their resins in-house.

    Our resin softens at just 60°C (140°F), which is the lowest in the industry. As such, you can reheat our resin as many times as required. That is to say; you can heat your boot and easily mold it to your foot. Following the heating, allow your boot to set and cool for your custom mold.

    Epoxy or polyepoxide is a thermosetting epoxide polymer that cures when mixed with a catalyzing agent or hardener. We control Polymerization, called curing, through temperature and the choice of resin and hardener compounds. The process can take minutes to hours.

    The amount of hardener added to the resin is critically dependent on the temperature of the air and the amount of humidity. For this reason, we have a computer that mixes the resin and hardener. This computer dispenses the resin after measuring the air temperature and humidity.

    Most manufacturers use a process known in the industry as pre-preg. A process that involves “pre-impregnating” resin into the carbon fiber.

    Pre-preg, in virtually all applications, the carbon fiber manufacturer chooses the resin. Its a one shoe fits all kind of deal. The boot manufacturer has no way of altering the resin customize heat moldability requirements of modern boots. For this reason, many competitors require high temperatures to make their boots heat moldable. Often the boot moldability is limited, even at these high temperatures.

  • HEAT MOLDING

    Bont manufactures the most heat moldable boots available in the market. Improved continuously for over 45 years, Bont proprietary resin is extremely stiff that becomes pliable at relatively low temperatures.

     

     

    Bont boots are moldable over the entire base, unlike other skates that are moldable only in select locations. Importantly, this provides skaters with the most anatomically designed boot on the market today. Additionally, skaters with Bont boots can fine-tune the fit of the whole boot to get that customized fit.

     

     

  • TEAM TESTING

    Our Bont Quadstar team are some of the best skaters in the World. They love to give us feedback! From the little things like the placement of the buckle to trialing the latest materials, they help Bont create products that not only look good but perform at the elite international level.

  • ANATOMICAL FOREFOOT SHAPE

    Conventional quad roller skates offer a “dress shoe” type shaping. Although highly aesthetic, this will cause the toes along with the metatarsals to be overly constricted. In turn, this compresses the nerves between the metatarsals, which often results in the common “hot foot” sensation.

    Bont’s anatomical shaping allows the foot to function in its most efficient and anatomically correct position. Also, the ability to heat mold any of our boots means you can get the right fit for your foot. 

    Anatomical Forefoot Shape
  • ANATOMICAL HEEL CUP

    The anatomical heel cup shaping of Bont quad roller skates provides increased stability and more power through your push. This stabilization is achieved without any mechanical operation or over tightening of straps/laces allowing for increased comfort and blood circulation. The heel cup is fully heat moldable to help get the prefect fit.

    Anatomical Heel Cup

  • ANTI-ABRASION MICROFIBER TOE PROTECTOR

    The anti-abrasion toe protector protects the front of your roller skate boot from scuffing and crashes.

    Anti-Abrasion Toe Protector
  • LIGHT WEIGHT

    At Bont, we pride ourselves at being lighter and stronger than the competition. That is why we manufacture our boots by hand, building the boot from the inside out by hand laying the carbon or fiberglass around the last (plastic foot). This method of manufacturing is extremely time consuming compared to the traditional method of skate boot manufacturing but ensures light weight.
  • LINER SUEDE-L

    We reviewed hundreds of different types of Liners before choosing a suitable product to use in our Bont boots. Our Suede-L liners are light-weight, durable, fight odor, and do not easily break down with sweat. Additionally, Bonts Suede-L is Vegan friendly.

    Liner Suede-L